Total items: 741
Order by:

HOMAG PROFI FKF 200

The machine for processing and revetting of board shields PROFI FKF 200 PROFI FKF200 / 13 / WH / F MACHINE FOR HANDLING AND FACING OF SHIELDS OF SHIELDS HOMAG PROFI FKF 200 For laminating coating materials in the form of rolls and sheets with the help of PU-hot melt adhesive on top of flat horizontal supporting plates in continuous mode. BASIC MACHINE: - the base machine consists of individual components that can be selected individually - service side on the right, left on request - painting of the machine and safety racks according to RAL 9003 signal white - designer strips, guard rails, doors in the guard rails and steles according to RAL 7021 black and gray - for Homag Group: - feed lock with interlock circuit and connecting cable - emergency lock - connecting cable to the machine according to the installation plan - feed rate: 5 - 25 m / min. - working height: 900 mm - pneumatic connection: 6 bar - performance data are the maximum possible values ​​by which materials used influence 2. PREPARATIONS AND FILMS: - min workpiece width: 200 mm - max. workpiece width: 1300 mm - min workpiece length: 1200 mm - max. workpiece length, depending on the filling station 3000 mm - workpiece thickness 8 - 80 mm - min film width: 200 mm - film width max. 1300 mm film roll: 600 mm - inner diameter: 76 mm - inner diameter (optional) 152 mm 3. MATERIALS AND PROCESSING PARAMETERS: 3.1 SUPPORTING MATERIAL: - allowances for processing: - along the length of the workpiece min. + 5 mm - over the width of the workpiece: min. + 5 mm - Particleboard: according to DIN EN 312 - MDF: according to DIN 622-5 - HDF sanded: to DIN 622-2 - lightweight boards are calibrated and ground by the Customer - tolerances oriented to DIN EN 312 - without protrusions of a crossbar or honeycombs along / across - warping of the workpiece should not exceed 2 mm - wood moisture: 6 - 8% - thickness tolerances: +/- 0.2 mm / m - width tolerances: +/- 0.2 mm / m 3.2 MATERIAL FOR FACING: Coating material in rolls: - PVC, PP, PET films max. 0.6 mm primed - decor paper from 30 g / m2 - the roll material is manually separated by the machine operator at the entrance to the machine! Sheet Coating Material: - HPL, CPL, PMMA, PET - coating materials must be suitable for lamination! Adhesive Type: - PU hot melt adhesives (as standard in two kilogram tanks for melting in roll gap, or optional smelters) 3.3 PROCESSING TEMPERATURE: - inlet temperature of the raw board min. 18 deg. - at low temperatures, line performance decreases 4. ELECTRICAL EQUIPMENT: Be sure to indicate the voltage (base 400 V / 50 Hz) - operating voltage ... V, ... Hz - free-standing distribution cabinet - connecting cable to the machine according to the installation plan - installation according to the Euronorm EN 60204 - electronic frequency converter with engine braking function - The circuit breaker is only allowed in combination with a circuit breaker sensitive to all types of current. If the power of this device is not sufficient, it is recommended to use a differential current monitoring device in place. - prescribed ambient temperature: from + 5 to + 40 ° C (at an operating temperature above 35 degrees or an air humidity of more than 65%, it is recommended cooling unit for the control cabinet) 6. SAFETY AND PROTECTION DEVICES: - the CE mark in accordance with the current machinery directive for the EU countries when operating individual machines in accordance with the machinery directive in the established countries, an additional assessment of compliance with the EU directive will be required for machine lines (a set of equipment / factory installations). List of countries and execution according to No. 8945 - a condition for our warranty / responsibility for the product is unconditional compliance with the original operating instructions and safety instructions supplied with the machine 6. INITIAL COMPOSITION OF INSTRUCTIONS FOR USE: - language in accordance with the one specified in pos. D.01 1. The operating instructions consist of the operation and maintenance manual on DIN A4 paper and electronic media 2. Designation of spare parts on electronic media 3. Electronic circuit diagrams in German and English 4. Help texts are integrated into the machine control 5. Dialogs of the operating system in English DRIVING ROLANGANE INLET LENGTH 3000 MM - prepared for installation of a brush unit for dust removal and preheating blanks - with a guide ruler on the right, which is manually adjusted to the thickness of the workpiece digital counter spindle with infinitely variable drive max. working width: 1300 mm roller table length: approx. 3000 mm max. workpiece length: 3500 mm PACK FOR THIN / SHORT PARTS - consists of rollers for feeding and unloading - min part length: 800 mm (instead of 1200 mm) - min part thickness: 3 mm (instead of 8 mm) G.0013 Number: 5561 1 x left BRUSH CLEANING UNIT FROM TOP

Location: Russian Federation
Producer: OTHER
Type: Wood
Year: 2016
Price: On request

Total items: 741
Order by:
Homogenizing of aluminium billet logs furnace
New arrival - DE

Homogenizing of aluminium billet logs furnace

Year: 2008

Price: On request

Nolting 150-190kW boiler

Year: 2018

Price: On request

Politechnik boiler

Year: 2005

Price: On request

lintel production line

Year: 2018

Price: On request

NHP 5000 Doosan
New arrival - IE

NHP 5000 Doosan

Year: 2019

Price: On request

Furnace for roller
New arrival - DE

Furnace for roller

Year: 2015

Price: On request

tacchi series 105 LS
New arrival

tacchi series 105 LS

Year: 2011

Price: On request

Industrial oven
New arrival - DE

Industrial oven

Year: 2017

Price: On request

2012 DMG CTV250
New arrival - DE

2012 DMG CTV250

Year: 2012

Price: On request

Tschudin HTG Type TL-25A
New arrival - ES

Tschudin HTG Type TL-25A

Year: 2014

Price: On request

A.V.M. Angelini Mach-2C vertical lathe
New arrival - DE

A.V.M. Angelini Mach-2C vertical lathe

Year: 2008

Price: On request

Oven
New arrival - DE

Oven

Year: 2017

Price: On request

Emco E 45
New arrival - DE

Emco E 45

Year: 2012

Price: On request

HSH furnace
New arrival - DK

HSH furnace

Year: 2009

Price: On request

MCM CLOCK 600
New arrival - DE

MCM CLOCK 600

Year: 2001

Price: On request

Complete automatic packing line for apple Germany
New arrival - PL
marel Live bird handling poultry farming 1
New arrival - DE

marel Live bird handling poultry farming 1

Year: 2010

Price: On request

precast concrete production machine
New arrival - FR

precast concrete production machine

Year: 2014

Price: Low price

Ewamatic
New arrival - DE

Ewamatic

Year: 2022

Price: Low price

Scroll to Top